Work flow of bag blister machine:

?

Vacuum plastic machine

1. Start the power supply system first;

2. Start the air source, the air pressure is required to be 5-6 kg;

3. Start the chiller and adjust the temperature of the chiller to about 10 degrees

4. Press the thermoplastic power switch and press ON to make the three power indicators turn on at the same time

5. Then press the electric furnace heating button and the main light will turn on, meaning that the electric furnace will be opened, and the heating control will be adjusted.

6. Arrange the molds and cover them with adhesive paper.

7. Press the middle brake at the very back of the mold.

8. Make good adjustment of the mold frame that needs to be put on the mold

9. Adjust the heat shield to the length of the mold.

10. Put the glue into the front fabric rack and fix it. Adjust the feed port

11. Adjust the drawing count length to the length of the machine mold (the counter length is adjusted by MODE, such as SET2 is displayed as the drawing length (such as 1000MM). Press MODE to show SET1 as a pull-buffer less than SET2. (if 850MM). RST is reset. When manually pulling the number to the count should be reset according to RST. Also check whether RST is reset before turning on automatic).

12. To manually start each switch is normal.

13. Adjust all your timings.

Note: Electric furnace time is the total time

The vacuum + water spray + demoulding blow + delay vacuum +1-2 seconds should not be more than the electric furnace time # film thickness and time ratio

Take 0.5 glue = 20 Take 0.5 glue = 20 # 1 # piece for 1 second

14. Degree forming height adjustment of middle brake, slitting, proximity switch position and row level nut.

15. Start the heating furnace, adjust the heating area of the heating furnace according to the molding area of the mold, adjust the temperature control device, observe the corresponding current and the red phenomenon of the heating brick, the general current is high around, low in the middle.

16. Install the film on the feed shaft, adjust the rake according to the width of the film and the position of the feed port, and fix the feed rotor at the corresponding position of the sheet feed positioning wheel.

17. After the heating furnace is preheated for 10 to 15 minutes and the temperature meets the production requirements, adjust the corresponding digital display time of each program on the control panel, generally set as the heating time number is greater than the vacuum, the addition time number of cold air and demoulding, and open the vacuum pump.

18. Lift the furnace, manually and automatically switch the phone, the feed switch selects the corresponding gear to place the sheet parallel between the press wheel and the chain teeth, click the pull button, and send the material into the heating area. At this time, the sheet should extend about 20mm from the exit of the lower brake.

19. Put the heating furnace down, manual, automatic switch automatic, heating time start, in the production of the first piece of product, the heating time should be set at more than 1.5 times the process required time, start the brake, observe the sheet heating condition, when the sheet heating area to meet the molding temperature, the point in advance to pull the sheet, so that the sheet is driven by the chain out of the heating area. Enter the molding action and modify the set number of heating times.

20. After the sheet is formed and cooled, the chain takes it out of the forming area and enters the cutting area. At this time, the tool brake should be closed, the feeder box should be moved, the feeder box should be positioned well after adjusting the cutting position, and the tool brake should be opened.

21. When the bag plastic machine automatically produces, the operator should check the product quality, see whether the temperature meets the product quality requirements, adjust the temperature, and then check in detail whether the uniformity of the film molding of the production variety is consistent, carry out local temperature adjustment, and maintain the quality requirements of the product.

22. Secondary die: used to protect the release of the product, the product is not deformed, no cracks, fragile, difficult to release the product used. Function setting: Select the upper die function in the secondary upper die. When the upper die reaches the surface of the product, the cold air stops and the bottom air begins to blow. Adjust the time of the secondary upper mold down to: the spray time count to the time value and the cold air count to the time value less than 2 seconds. If the upper mold is down too early, the use of water spraying will be increased, and otherwise, the water spraying time will be reduced.

23. Vibration demoulding: Usually used in products with higher or deeper molding and difficult demoulding. The button of the shock release is open, and the blowing time is set at more than 2 seconds, which is set according to the number of vibration of the product. The more the number of vibration, the longer the blowing time is set. Open the control box on the lower right, and there are two 10-second timings. The left time system controls the time under the lower die, the right control the total time of the next cycle of the die disk, and according to the reaction of the die disk up and down the throttle valve, the electrical combination to achieve the purpose of vibration.

24. Electric synchronous mode adjustment: According to the need of the combination of upper and lower modes, when the functional button is selected to rise, the point modulated mode overmoves, the upper mode rises, and the reverse mode falls.

25. Advance drawing: in the heating time, start the lower brake, observe the heating of the sheet, meet the product forming requirements, click the button, so that the sheet in the chain driven out of the heating area, into the forming action.

26. Off the brake: this function can be operated in manual and automatic state, manual can be partially adjusted, in automatic, to observe the sheet heating condition.

27. Stop brake: In the automatic state, according to the needs of product molding, the upper brake will be closed without using the upper brake.

Stop brake: In the automatic state, after the product is formed and cooled, when entering the cutting area, for safety reasons, close the brake, adjust the cutting position and fix the receiving box before opening.

28. Setting method of electronic counter:

1) In the setting state: When the required MODE is displayed, press the mode key to select and proceed to the next step, and press DISPLAY at any step to end the setting;

2) Press the MODE key to check the Settings;

3) The SET2 value of the two sets of products must be greater than the SET1 value. If the SET1 value is less than or equal to the SET1 value, FFFFFF will be displayed to remind users to modify it. After modification, please press the panel RESET key RESET, FFFFFF will disappear (if FFFFFF is displayed, the key protection will have no effect on the reset lock of the panel. Until FFFFFF disappears);

4) After the setting is completed, please use the key protection function to protect the data you set from being changed by others (key protection only works when the KP connected to the first terminal is connected to the public end, and the display of K/P indicates that the key protection function has worked).?

Learn more：http://jjjl2008.cn